Skip to main content
Analog Devices MAX1302AEUG+ — DC-DC Power Modules

MAX1302AEUG+ 16-bit SAR ADC, 115k SPS, SPI, 24-TSSOP

MPNMAX1302AEUG+
End of Life

Maxim Integrated MAX1302AEUG+, 16-bit SAR ADC, 115k SPS, SPI, MUX-PGA-S/H-ADC, 4/8 differential/single-ended inputs, 5V supply, 24-TSSOP, -40°C to 85°C.

$23.94Ref. price · indicative, final on quote
Packaging24-TSSOP (0.173", 4.40mm Width)
RoHSROHS3 Compliant
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

MAX1302AEUG+ specifications
ParameterValue
Input typeDifferential, Single Ended
MountingSurface Mount
Reference typeExternal, Internal
Voltage - supply, analog5V
Voltage - supply, digital5V
I/O channels4, 8
InterfaceSPI
Operating temperature-40°C ~ 85°C
PackageTube
FeaturesPGA
ArchitectureSAR
ConfigurationMUX-PGA-S/H-ADC
Number of bits16
Case24-TSSOP (0.173\", 4.40mm Width)
Ratio - s (H:ADC)1:1
Number of a (D converters)1
Sampling rate (Per second)115k

Product details

16-bit SAR with on-chip PGA — one part replaces a signal chain

The Maxim Integrated MAX1302AEUG+ is a 16-bit successive-approximation-register (SAR) ADC that integrates an input multiplexer, a programmable-gain amplifier (PGA), and a sample-and-hold into a single 24-TSSOP package. It samples at 115k samples per second over the SPI bus, accepting either differential or single-ended inputs through its 4 or 8 input channels (configured as 4 differential or 8 single-ended). The internal PGA lets you amplify small sensor signals before conversion, saving an external op-amp stage and its associated BOM cost and board area.

115k SPS at 16 bits — where the speed fits

At 115k samples per second and 16-bit resolution, this ADC sits in the sweet spot for industrial data-acquisition systems that need moderate throughput with real dynamic range. A 16-bit conversion at 115k SPS gives an LSB size of about 76 µV on a 5 V reference — enough to resolve thermocouple, strain-gauge, or pressure-sensor outputs without external gain. The SAR architecture means no pipeline delay: the conversion result for a given sample is available on the next SPI transaction, which simplifies real-time control loops.

Differential or single-ended — 4 or 8 channels

The input multiplexer gives you a choice: four differential pairs or eight single-ended inputs. Differential mode rejects common-mode noise on long sensor leads, which matters in factory-floor or motor-drive environments where ground loops are common. Single-ended mode doubles the channel count for monitoring multiple DC voltages or logic-level signals. The on-chip PGA provides selectable gain, letting you match the input range to the sensor output without external resistors.

5 V supply, SPI interface, industrial temperature range

The SPI data interface uses four wires (SCLK, DIN, DOUT, CS) and is compatible with most microcontrollers and DSPs — no parallel bus or address decoding needed. The 24-TSSOP package with 0.173-inch body width fits on compact PCB layouts.

ROHS3 compliant per, so it meets the latest EU restriction directives.

Frequently asked questions

Is MAX1302AEUG+ compatible with SPI interface?

Yes, the data interface is SPI. It uses standard SCLK, DIN, DOUT, and CS signals, making it directly compatible with the SPI peripheral on most microcontrollers without glue logic.

What is the resolution of MAX1302AEUG+?

The MAX1302AEUG+ is a 16-bit ADC. At 115k samples per second with a 5 V reference, the LSB size is approximately 76 µV.

Does MAX1302AEUG+ support differential inputs?

Yes, it supports both differential and single-ended inputs. The 8 input channels can be configured as 4 differential pairs or 8 single-ended inputs.