Skip to main content
Texas Instruments LME49726MY/NOPB — Memory (DRAM / SRAM / Flash / EEPROM)
Texas Instruments

LME49726MY/NOPB Audio Op-Amp, 6.25 MHz, Rail-to-Rail Output

MPNLME49726MY/NOPB
End of Life

Texas Instruments LME® series, Audio Amplifier, 2 Circuit, Rail-to-Rail, 8-HVSSOP package, 6.25 MHz gain bandwidth, 3.7 V/µs slew rate, 2.5 V to 5.5 V supply.

$1.96Ref. price · indicative, final on quote
LME49726MY/NOPB datasheet
Packaging8-TSSOP, 8-MSOP (0.118", 3.00mm Width) Exposed Pad
StockContact for availability
MOQ1 pcs
  • 100% new & originalTraceable channels only — no refurbs, no pulls, no remarked parts.
  • Date & lot codes on quoteStated per line before you commit; label photos on request.
  • MSL-compliant ESD packingMoisture-sealed bags with indicator cards; reels photo-verified.
  • PayPal buyer protectionPay by T/T, PayPal or Payoneer — card payments covered end to end.

Specifications

LME49726MY/NOPB Technical Specifications
ParameterValue
SeriesLME®
Output typeRail-to-Rail
Mounting typeSurface Mount
Amplifier typeAudio
Voltage - input offset500 µV
Voltage - supply span5.5 V
Current - supply700µA (x2 Channels)
Current - input bias0.2 pA
Current - output (Channel)350 mA
Operating temperature-40°C ~ 85°C
Gain bandwidth product6.25 MHz
PackageTape & Reel (TR); Cut Tape (CT)
Slew rate3.7V/µs
Case8-TSSOP, 8-MSOP (0.118\", 3.00mm Width) Exposed Pad
Number of circuits2

Product details

Audio op-amp with headphone-grade output drive

The Texas Instruments LME49726MY/NOPB is a dual audio operational amplifier from the LME® series, with two rail-to-rail output stages in an 8-HVSSOP package. It delivers a 6.25 MHz gain-bandwidth product and a 3.7 V/µs slew rate.

350 mA output — what it means for the audio chain

The LME49726MY/NOPB's 350 mA output per channel can drive headphones directly, saving board area and BOM cost. The exposed pad on the 8-HVSSOP package requires a solid thermal via array to the ground plane.

Supply and temperature range — field-fit check

The part runs on 2.5 V to 5.5 V total supply, single or split. The -40°C to 85°C temperature range covers outdoor telecom cabinets, automotive cabin audio, and factory-floor public-address systems.

Active lifecycle — no LTB pressure on the BOM

TI lists the LME49726MY/NOPB as Active with ROHS3 compliance. No NRND flag, no last-time-buy notice as of the current record. The part is sourced through independent distribution and quoted to order against an RFQ.

Frequently asked questions

Where can I buy LME49726MY/NOPB with stock?

This part is sourced to order through independent distribution. Submit an RFQ for current availability and pricing — stock levels and lead times are confirmed at the time of quotation.

What is the difference between LME49726MY/NOPB and LME49720?

The LME49720 is a higher-performance sibling with a 55 MHz GBW and 20 V/µs slew rate, targeting ultra-low-distortion preamplifier stages. The LME49726 trades top-end bandwidth for lower supply current (700 µA per channel vs roughly 5 mA per channel on the 49720) and adds the 350 mA output drive for headphone loads. The 49726 is the better fit for battery-powered or output-drive applications; the 49720 suits line-level signal processing where maximum bandwidth and lowest noise matter more.

Is there a direct replacement for LME49726MY/NOPB?

There is no single pin-compatible drop-in from another manufacturer listed as a direct replacement. The OPA4374AIPWT from TI is a quad CMOS op-amp with similar bandwidth (6.5 MHz) and rail-to-rail output, but it is a quad package (not dual) and its output current is only 5 mA — not suitable for headphone drive. For a dual-channel audio op-amp with high output current, the LME49726MY/NOPB is the specific part; no exact second-source alternate is documented in the current record.