Skip to main content
Log in
STMicroelectronics VNL5300S5TR-E — Analog & Data Acquisition

VNL5300S5TR-E STMicro Low-Side Driver, 300 mOhm, 2A, 8-SOIC

MPNVNL5300S5TR-E
End of Life

STMicroelectronics OMNIFET III™, VIPower™ series VNL5300S5TR-E, IC PWR DRIVER N-CHANNEL 1:1 8SO, low-side driver, 300mOhm typical Rds(on), 2A max output, 8-SOIC surface mount, -40°C to 150°C junction temperature.

$1.06Ref. price · indicative, final on quote
STMicroelectronics VNL5300S5TR-E datasheet (PDF)
Packaging8-SOIC (0.154", 3.90mm Width)
RoHSROHS3 Compliant
SeriesOMNIFET III™, VIPower™
Independent supplier — new & surplus stockAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

VNL5300S5TR-E specifications
ParameterValue
SeriesOMNIFET III™, VIPower™
Input typeNon-Inverting
Output typeN-Channel
TypeGeneral Purpose
MountingSurface Mount
Voltage - load36V (Max)
Voltage - supply (Vcc (Vdd))3.5V ~ 5.5V
Output current2A
I/O channels1
InterfaceOn/Off
Operating temperature-40°C ~ 150°C (TJ)
PackageTape & Reel (TR); Cut Tape (CT)
FeaturesAuto Restart, Status Flag
Rds on300mOhm
Case8-SOIC (0.154\", 3.90mm Width)
Fault protectionCurrent Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO
Output configurationLow Side
Ratio - Input:Output1:1

Product details

300 mOhm Rds(on) — sizing the load and the thermal budget

The STMicroelectronics VNL5300S5TR-E is a single-channel low-side N-channel power driver from the OMNIFET III and VIPower families. It switches a grounded load up to 2 A continuous with a typical on-resistance of 300 mOhm. The 150 °C junction rating gives headroom for engine-bay or motor-drive environments, but the board layout is what makes that rating real.

Fault protection set — what it saves you on the BOM

That protection suite replaces a handful of discrete comparators and a current-sense resistor. The auto-restart feature means it recovers after a fault without a system reset — useful for a solenoid or lamp load that might draw inrush.

5 V logic compatible — no level shifter needed

Tie the input to a GPIO or a PWM timer — the on/off interface is simple, no external translation required. The status flag output gives a clean low when a fault is active, which can feed an interrupt line or a diagnostic LED.

No last-time-buy notice, no end-of-life pressure.

Frequently asked questions

What is the Rds(on) of VNL5300S5TR-E?

The typical on-resistance is 300 mOhm. That is the figure you use for thermal calculations at nominal current; the datasheet will show the max at temperature.

Does VNL5300S5TR-E have over-temperature protection?

Yes, it includes over-temperature shutdown as part of its fault protection set, along with current limiting, open-load detect, over-voltage clamp, and UVLO.

Is VNL5300S5TR-E compatible with 5V logic?

Yes. The input is non-inverting and the interface is on/off — no level shifter needed.

When sourcing VNL5300S5TR-E, what is the closest functional second-source?

The TDE1747FPT is a different device — it is a high-side bipolar relay/solenoid driver with a 1 A output and a narrower temperature range (-25°C to 85°C). It is not a pin-compatible or functional replacement for this low-side N-channel driver. For a true second source, look at other ST OMNIFET III parts in the same package and current class.