Skip to main content
Toshiba Semiconductor TLP385(D4GL-TL,E — Optoisolators

TLP385(D4GL-TL,E Optocoupler, 5000Vrms, 50-600% CTR, 6-SOIC

MPNTLP385(D4GL-TL,E
End of Life

Toshiba TLP385(D4GL-TL,E transistor output optocoupler, 1 channel, DC input, 5000Vrms isolation, 50% to 600% CTR at 5mA, 80V output, 6-SOIC-4 surface mount, -55°C to 110°C.

$0.54Ref. price · indicative, final on quote
Packaging6-SOIC (0.173", 4.40mm Width), 4 Leads
StockContact for availability
MOQ1 pcs
  • 100% new & originalTraceable channels only — no refurbs, no pulls, no remarked parts.
  • Date & lot codes on quoteStated per line before you commit; label photos on request.
  • MSL-compliant ESD packingMoisture-sealed bags with indicator cards; reels photo-verified.
  • PayPal buyer protectionPay by T/T, PayPal or Payoneer — card payments covered end to end.

Specifications

TLP385(D4GL-TL,E Technical Specifications
ParameterValue
Input typeDC
Output typeTransistor
Mounting typeSurface Mount
Voltage - isolation5000Vrms
Voltage - output80V
Voltage - forward (Vf)1.25V
Current - output (Channel)50mA
Current transfer ratio600% @ 5mA
Current - DC forward (If)50 mA
Operating temperature-55°C ~ 110°C
PackageTape & Reel (TR); Cut Tape (CT)
Case6-SOIC (0.173\", 4.40mm Width), 4 Leads
Number of channels1
Vce saturation300mV
Rise (Fall time)2µs, 3µs
Turn on (Turn off time)3µs, 3µs

Product details

The Toshiba TLP385(D4GL-TL,E is a single-channel transistor-output optocoupler in a 4-lead 6-SOIC surface-mount package. It provides 5000Vrms of galvanic isolation between a DC input LED and a phototransistor output, with a current transfer ratio (CTR) ranging from 50% to 600% at a forward current of 5mA. This part is suited for industrial control interfaces, PLC I/O modules, motor drive feedback, and any application requiring reinforced isolation between logic-level signals and higher-voltage circuits. The -55°C to 110°C operating temperature range covers most industrial and some automotive environments without derating.

The 5000Vrms isolation rating is the headline safety spec. It qualifies this optocoupler for reinforced insulation in mains-connected equipment — think AC motor drives, switched-mode power supply feedback, and industrial sensors that must survive transient overvoltages without bridging the safety barrier. For a procurement decision, this rating is non-negotiable: if your design requires 5000Vrms, the TLP385(D4GL-TL,E fits without margin questions. If your application only needs basic isolation at 2500Vrms, you could step to a lower-rated part and save board area, but the 6-SOIC-4 footprint here is already compact.

CTR range — matching the LED drive to the load

The CTR window of 50% to 600% at 5mA forward current is wide. That means the same part can work with a low-drive microcontroller pin (CTR on the high side) or a high-drive logic output (CTR on the low side), as long as the load-side collector current requirement falls within the product of CTR and forward current. For a typical 5mA input, the output can sink between 2.5mA and 30mA — enough to drive a logic gate input, a relay coil via a transistor, or an LED indicator. The wide spread also means you should design for the minimum CTR to guarantee operation across temperature and LED aging; the 50% floor at 5mA gives a 2.5mA guaranteed output.

Lifecycle and supply posture

No last-time-buy or end-of-life notification is on file. RoHS compliant.

Frequently asked questions

What is the current transfer ratio (CTR) of TLP385(D4GL-TL,E?

The CTR ranges from 50% minimum to 600% maximum, both measured at a forward current of 5mA. This wide range covers low-drive and high-drive input scenarios.