Skip to main content
Analog Devices MAX314CSE+T — Interface & Transceivers

MAX314CSE+T Analog Devices SPST Switch, 10 Ohm, 16-SOIC

MPNMAX314CSE+T
End of Life

Analog Devices MAX314CSE+T, SPST NO/NC analog switch, 4 circuits, 10 Ohm on-resistance, 16-SOIC surface mount, -85dB crosstalk @ 1MHz, Tape & Reel.

$7.38Ref. price · indicative, final on quote
Packaging16-SOIC (0.154", 3.90mm Width)
StockIn Stock (26)
Lead timeIn Stock wk
MOQ1 pcs
  • 100% new & originalTraceable channels only — no refurbs, no pulls, no remarked parts.
  • Date & lot codes on quoteStated per line before you commit; label photos on request.
  • MSL-compliant ESD packingMoisture-sealed bags with indicator cards; reels photo-verified.
  • PayPal buyer protectionPay by T/T, PayPal or Payoneer — card payments covered end to end.

Specifications

MAX314CSE+T Technical Specifications
ParameterValue
Mounting typeSurface Mount
Voltage - supply, dual (V±)±4.5V ~ 20V
Voltage - supply, single (V+)4.5V ~ 30V
Current - leakage (IS(off))500pA
Operating temperature0°C ~ 70°C (TA)
PackageTape & Reel (TR); Cut Tape (CT)
Crosstalk-85dB @ 1MHz
Case16-SOIC (0.154\", 3.90mm Width)
Switch circuitSPST - NO/NC
Charge injection20pC
Number of circuits4
On-State resistance10Ohm
Switch time (Ton, toff)225ns, 185ns
Multiplexer (Demultiplexer circuit)1:1
Channel capacitance (CS(off), CD(off))15pF, 15pF
Channel-to-Channel matching (ΔRon)300mOhm

Product details

Active production, 4-channel SPST with ±4.5V to 20V dual supply

The MAX314CSE+T is an active-production, 4-circuit SPST analog switch from Analog Devices, configurable as normally-open or normally-closed per channel. It operates from a single 4.5V to 30V rail or dual ±4.5V to 20V supplies, making it suitable for bipolar signal chains and single-supply data-acquisition systems. On-resistance is 10 Ohm max, with channel-to-channel matching of 300 mOhm — the matching figure matters more than the absolute Ron when switching gain-setting resistors or precision dividers, because the offset error between channels stays below 0.3 Ohm.

Dynamic performance: 225 ns switching, -85 dB crosstalk

Maximum turn-on time is 225 ns, turn-off 185 ns — fast enough for audio multiplexing, sensor scanning at 100 kHz rates, and relay-replacement in ATE pin electronics. Charge injection is 20 pC typical, which translates to a ~1.3 mV glitch into a 15 pF load; keep the downstream ADC input settled within one conversion cycle. Crosstalk is -85 dB at 1 MHz, and off-channel leakage is 500 pA max. In a 16-channel system, the summed leakage from 15 off channels is under 7.5 nA — negligible for a 10 kΩ source impedance but worth derating for high-impedance front-ends above 1 MΩ. Channel capacitance is 15 pF on both source and drain sides. This sets the bandwidth ceiling: into a 10 kΩ load, the -3 dB pole is roughly 1 MHz, matching the crosstalk test frequency. For video or high-speed ADC drivers, buffer the output.

16-SOIC surface-mount package, commercial temperature grade

The 1.27 mm pin pitch is layout-friendly — two-layer boards route the analog and supply traces without via congestion under the package. This covers lab instrumentation, office-environment data acquisition, and telecom line cards with forced air. Not specified for -40°C operation — if the BOM requires industrial temperature, look at the MAX314C/D or MAX314EPE variants from the same family.

For BOM planning, this part is a safe anchor through 2025 and beyond, assuming normal product lifecycles.

Frequently asked questions

What is the listed crosstalk for MAX314CSE+T?

Crosstalk is specified at -85 dB at 1 MHz. This means a signal on one channel couples into an adjacent off channel at roughly 56 µV per volt of signal — adequate for 12-bit systems with 2 V p-p signals, but borderline for 16-bit precision multiplexing above 100 kHz.