{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"TL084HIDR","brand":"Texas Instruments","brandSlug":"texas-instruments","productSlug":"TL084HIDR","canonicalUrl":"https://icboms.com/texas-instruments/TL084HIDR","factsUrl":"https://icboms.com/api/mcp/products/TL084HIDR","rawCanonicalId":null},"summary":{"shortDescription":"Texas Instruments TL084HIDR, quad JFET-input operational amplifier, 5.25 MHz gain bandwidth, 20V/µs slew rate, 4.5 V to 40 V supply, 14-SOIC package, -40°C to 125°C operating temperature.","salesMarkdown":"The TL084HIDR operates from a single supply as low as 4.5 V up to 40 V, or from dual supplies of ±2.25 V to ±20 V. That 4.5 V minimum means it runs cleanly from a 5 V rail without a boost converter, while the 40 V ceiling covers industrial 24 V and 36 V rails with margin. Each of the four amplifiers can source or sink 26 mA — enough to drive a 2 kΩ load to within a couple of volts of the rails, or to directly feed the input of a successive ADC without an extra buffer stage. Supply current per amplifier is 937.5 µA typical. For a quad part that is under 4 mA total quiescent — low enough that a 24 V loop-powered transmitter can run the whole amplifier section without exceeding the loop budget. ## Temperature grade and package — board-level fit The H suffix in the order code denotes this extended temperature grade, distinguishing it from commercial-temperature TL084 variants. For dual-sourcing resilience, the TL084 family is second-sourced by multiple manufacturers; the TL084CN in PDIP-14 is a through-hole sibling, but the HIDR suffix specifically identifies the surface-mount, extended-temperature variant.","metaTitle":"TL084HIDR Quad JFET Op-Amp, 20V/µs Slew Rate, 14-SOIC","metaDescription":"TL084HIDR quad JFET op-amp from TI: 5.25 MHz GBW, 20V/µs slew rate, 1 pA input bias, -40°C to 125°C.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Analog & Data Acquisition"],"specifications":{"Mfr":"Texas Instruments","Series":"-","Package":"Tape & Reel (TR); Cut Tape (CT)","Slew Rate":"20V/µs","Output Type":"-","Mounting Type":"Surface Mount","Amplifier Type":"J-FET","Package / Case":"14-SOIC (0.154\\\", 3.90mm Width)","Product Status":"Active","lifecycle_stage":"eol_hot","Current - Supply":"937.5µA","Number of Circuits":"4","Base Product Number":"TL084","Current - Input Bias":"1 pA","Operating Temperature":"-40°C~125°C(TA)","Gain Bandwidth Product":"5.25 MHz","Voltage - Input Offset":"1 mV","Supplier Device Package":"14-SOIC","Current - Output / Channel":"26 mA","Voltage - Supply Span (Max)":"40 V","Voltage - Supply Span (Min)":"4.5 V"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$0.5200","priceTiers":null},"links":{"datasheetUrl":"https://cdn.icboms.com/bd0d2120e3c12ca626ffeb622ac6a207.pdf","sourceUrl":null,"alternativesUrl":"https://icboms.com/api/mcp/products/TL084HIDR/alternatives.json"},"ai":{"faq":[{"question":"Can TL084HIDR replace TL084CN?","answer":"The TL084HIDR and TL084CN share the same TL084 core — same JFET input stage, same 5.25 MHz GBW, same 20 V/µs slew rate. If your board layout accepts the SOIC footprint and you need the extended temperature range, the HIDR is a functional replacement. Pinout is identical across the TL084 family."},{"question":"What is the slew rate of TL084HIDR?","answer":"The TL084HIDR has a slew rate of 20 V/µs. This is the large-signal bandwidth limit — for a 10 V output swing, the amplifier can transition in 0.5 µs, which supports audio-frequency and moderate-speed control loops without slew-induced distortion."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/texas-instruments/TL084HIDR","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/texas-instruments/TL084HIDR when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T18:03:28.771Z","lastPublished":"2026-07-22T18:03:28.771Z","indexable":true}}