{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SN65LVDS050PWR","brand":"Texas Instruments","brandSlug":"texas-instruments","productSlug":"SN65LVDS050PWR","canonicalUrl":"https://icboms.com/texas-instruments/SN65LVDS050PWR","factsUrl":"https://icboms.com/api/mcp/products/SN65LVDS050PWR","rawCanonicalId":null},"summary":{"shortDescription":"Texas Instruments 65LVDS series LVDS transceiver, full duplex, 400 Mbps data rate, 2 drivers / 2 receivers, 3V to 3.6V supply, -40°C to 85°C, 16-TSSOP package, Tape & Reel.","salesMarkdown":"## Active-production LVDS transceiver for 400 Mbps point-to-point links This part is designed for high-speed differential data transmission over controlled-impedance PCB traces or short cable runs, where LVDS provides low EMI and low power dissipation compared to single-ended alternatives at similar data rates. The 400 Mbps rating is the per-channel data rate, not a combined aggregate. Each of the two driver/receiver pairs can sustain a 400 Mbps serial stream independently. For a typical 8-bit parallel bus serialised with an LVDS serializer, this translates to a 50 MHz parallel clock rate at 1:8 serialisation. The 400 Mbps figure is the minimum guaranteed over supply and temperature — the actual eye opening at the receiver input will be wider at nominal 3.3 V and 25°C, but the spec ensures timing closure across the full industrial range. The 300 mV margin on each side of 3.3 V covers typical regulator tolerance and ripple. If your board already has a 3.3 V rail for the FPGA or SoC bank, this transceiver shares it — no extra voltage plane needed. The full-duplex LVDS link maintains its 400 Mbps data rate across the entire temperature band — no derating required. If your application requires 105°C or 125°C ambient, you would need to step up to an automotive-grade LVDS part with a wider Tj range. This means the part is in ongoing production with normal lead times through authorised distribution. ## 16-TSSOP package — footprint and layout The SN65LVDS050PWR is supplied in a 16-lead TSSOP package with 0.65 mm pitch and a 4.4 mm body width. This is a common, widely supported footprint used across TI's LVDS and interface portfolio. No thermal pad or exposed paddle — standard FR-4 PCB with 0.65 mm pitch land pattern is sufficient.","metaTitle":"SN65LVDS050PWR LVDS Transceiver, 400 Mbps, 16-TSSOP, Active","metaDescription":"Texas Instruments SN65LVDS050PWR is a full-duplex LVDS transceiver with 2/2 drivers/receivers, 400 Mbps data rate, 3V-3.6V supply, -40°C to 85°C.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Interface & Transceivers"],"specifications":{"Mfr":"Texas Instruments","Type":"Transceiver","Duplex":"Full","Series":"65LVDS","Package":"Tape & Reel (TR)","Protocol":"LVDS","Data Rate":"400Mbps","Mounting Type":"Surface Mount","Package / Case":"16-TSSOP (0.173\\\", 4.40mm Width)","Product Status":"Active","lifecycle_stage":"eol_hot","Voltage - Supply":"3V ~ 3.6V","Base Product Number":"65LVDS050","Operating Temperature":"-40°C~85°C","Supplier Device Package":"16-TSSOP","Number of Drivers/Receivers":"2/2"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$2.4015","priceTiers":null},"links":{"datasheetUrl":"https://cdn.icboms.com/ed6dad5d68c9d6c0b1007b7931e3aaed.pdf","sourceUrl":null,"alternativesUrl":"https://icboms.com/api/mcp/products/SN65LVDS050PWR/alternatives.json"},"ai":{"faq":[{"question":"What is the data rate of SN65LVDS050PWR?","answer":"The SN65LVDS050PWR supports a per-channel data rate of 400 Mbps."},{"question":"Is SN65LVDS050PWR compatible with 3.3V logic?","answer":"Yes. The LVDS outputs and inputs are differential and do not use single-ended 3.3 V CMOS levels on the bus, but the device supply and control logic (driver enable, receiver enable) are 3.3 V compatible."},{"question":"What is the difference between SN65LVDS050PWR and SN65LVDS050PW?","answer":"The SN65LVDS050PWR and SN65LVDS050PW are electrically identical — same transceiver, same 16-TSSOP package, same 400 Mbps data rate. The only difference is the packaging medium: the PWR suffix denotes Tape & Reel (suitable for automated assembly), while the PW suffix denotes tube packaging (often used for hand-assembly or low-volume prototyping)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/texas-instruments/SN65LVDS050PWR","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/texas-instruments/SN65LVDS050PWR when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:49:49.435Z","lastPublished":"2026-08-11T15:49:49.435Z","indexable":true}}