{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SN65HVD76DGSR","brand":"Texas Instruments","brandSlug":"texas-instruments","productSlug":"SN65HVD76DGSR","canonicalUrl":"https://icboms.com/texas-instruments/SN65HVD76DGSR","factsUrl":"https://icboms.com/api/mcp/products/SN65HVD76DGSR","rawCanonicalId":null},"summary":{"shortDescription":"Texas Instruments SN65HVD76DGSR, RS-422/RS-485 transceiver, full duplex, 50 Mbps data rate, 3V–3.6V supply, 70 mV receiver hysteresis, -40°C to 125°C, 10-VSSOP package.","salesMarkdown":"The 70 mV of receiver hysteresis provides noise margin on long cable runs where ground potential differences eat into the differential signal — a meaningful edge over parts with 30 mV or 50 mV hysteresis when the bus spans tens of metres through a factory floor. The 1/1 driver/receiver count suits point-to-point or multi-drop applications where one node talks and one listens full-time — think encoder feedback, VFD control links, or PLC-to-remote-I/O bridges. The 10-VSSOP (3.00 mm × 3.00 mm body, 0.50 mm pitch) is a standard small-outline package. The exposed pad is absent — it's a non-thermal package, so all heat conducts through the leads. Reflow profile follows standard lead-free (260°C peak). Hand rework with hot air at 320°C, 15 L/min, preheat the board to 100°C to avoid pad lifting on the thin 0.118-inch MSOP footprint. Bake at 125°C for 24 hours if the bag seal is broken and the humidity indicator card shows >30%. No last-time-buy or discontinuation notice has been issued.","metaTitle":"SN65HVD76DGSR TI RS-485 Transceiver, 50 Mbps Full Duplex","metaDescription":"Texas Instruments SN65HVD76DGSR RS-422/RS-485 transceiver, 50 Mbps full duplex, 3V–3.6V supply, 70 mV hysteresis, -40°C to 125°C.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Interface & Transceivers"],"specifications":{"Mfr":"Texas Instruments","Type":"Transceiver","Duplex":"Full","Series":"-","Package":"Tape & Reel (TR); Cut Tape (CT)","Protocol":"RS422, RS485","Data Rate":"50Mbps","Mounting Type":"Surface Mount","Package / Case":"10-TFSOP, 10-MSOP (0.118\\\", 3.00mm Width)","Product Status":"Active","lifecycle_stage":"eol_hot","Voltage - Supply":"3V ~ 3.6V","Base Product Number":"65HVD76","Receiver Hysteresis":"70 mV","Operating Temperature":"-40°C~125°C","Supplier Device Package":"10-VSSOP","Number of Drivers/Receivers":"1/1"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$4.5800","priceTiers":null},"links":{"datasheetUrl":"https://cdn.icboms.com/9087c32540c5c64471c20d05147d7cee.pdf","sourceUrl":null,"alternativesUrl":"https://icboms.com/api/mcp/products/SN65HVD76DGSR/alternatives.json"},"ai":{"faq":[{"question":"Can SN65HVD76DGSR be used with 3.3V microcontrollers?","answer":"Yes. The logic inputs are 3.3V-compatible, so no level shifting is needed when connecting to a 3.3V UART or SPI master."},{"question":"What is the difference between SN65HVD76DGSR and SN65HVD75DGSR?","answer":"The SN65HVD76DGSR is a full-duplex transceiver, while the SN65HVD75DGSR is half-duplex. Both share the same 50 Mbps data rate, 3V–3.6V supply, and 10-VSSOP package, but the full-duplex part uses separate driver and receiver enable pins and supports simultaneous transmit and receive on two twisted pairs."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/texas-instruments/SN65HVD76DGSR","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/texas-instruments/SN65HVD76DGSR when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:49:49.435Z","lastPublished":"2026-08-11T15:49:49.435Z","indexable":true}}