{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"OPA810IDBVR","brand":"Texas Instruments","brandSlug":"texas-instruments","productSlug":"OPA810IDBVR","canonicalUrl":"https://icboms.com/texas-instruments/OPA810IDBVR","factsUrl":"https://icboms.com/api/mcp/products/OPA810IDBVR","rawCanonicalId":null},"summary":{"shortDescription":"Texas Instruments OPA810IDBVR JFET operational amplifier, 254V/µs slew rate, 140 MHz -3dB bandwidth, rail-to-rail output, SOT-23-5 package, Tape & Reel.","salesMarkdown":"## JFET input stage for high-impedance sensor front-ends The OPA810IDBVR is a single-channel JFET-input operational amplifier from Texas Instruments, built for signal chains that need both wide bandwidth and low input bias current. With an input bias current of 2 pA typical, this part suits photodiode amplifiers, piezoelectric sensors, and other high-source-impedance front-ends where bias current drift would otherwise swamp the signal. The 254 V/µs slew rate and 140 MHz -3 dB bandwidth mean the amplifier can track fast transients — think high-speed data acquisition or wideband transimpedance stages — without slewing into distortion. Gain-bandwidth product is 70 MHz, so at a closed-loop gain of 10 the usable bandwidth is about 7 MHz before the open-loop roll-off cuts in. ## Rail-to-rail output and supply flexibility The push-pull rail-to-rail output stage swings within millivolts of both supply rails, maximising dynamic range in single-supply or low-voltage systems. Supply span runs from 4.75 V minimum to 27 V maximum, covering common 5 V and ±15 V rails as well as 12 V and 24 V industrial buses. Output can source or sink up to 100 mA per channel, enough to drive an ADC input, a coaxial cable, or a small relay coil directly. Input offset voltage is 100 µV typical — adequate for most precision signal conditioning but worth budgeting if the application demands sub-millivolt DC accuracy across temperature. ## SOT-23-5 package and rework reality Housed in a SOT-23-5 (SC-74A) package, the OPA810IDBVR is a five-pin surface-mount device with a 0.95 mm pitch — easy to hand-solder or rework with a fine-tip iron and hot air. Pin 1 is clearly marked by a chamfer on the package body, so orientation is unambiguous under a loupe or automated vision system. ## Industrial temperature range and active lifecycle Rated for -40 °C to +125 °C ambient, this amplifier is specified for industrial and automotive-adjacent environments — motor drives, engine-bay sensor interfaces, outdoor telecom gear.","metaTitle":"TI OPA810IDBVR JFET Op-Amp, 254V/µs Slew Rate, SOT-23-5","metaDescription":"Texas Instruments OPA810IDBVR JFET op-amp: 254V/µs slew rate, 140 MHz bandwidth, 2 pA input bias, rail-to-rail output, SOT-23-5.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":"Not applicable","productStatus":"Active","categoryPath":["Discrete Semiconductors"],"specifications":{"Package":"Tape & Reel (TR); Cut Tape (CT)","Slew Rate":"254V/µs","Output Type":"Push-Pull, Rail-to-Rail","Mounting Type":"Surface Mount","-3db Bandwidth":"140 MHz","Amplifier Type":"J-FET","Package / Case":"SC-74A, SOT-753","lifecycle_stage":"eol_hot","Current - Supply":"3.8mA","Number of Circuits":"1","Current - Input Bias":"2 pA","Operating Temperature":"-40°C ~ 125°C (TA)","Gain Bandwidth Product":"70 MHz","Voltage - Input Offset":"100 µV","Supplier Device Package":"SOT-23-5","Current - Output / Channel":"100 mA","Voltage - Supply Span (Max)":"27 V","Voltage - Supply Span (Min)":"4.75 V"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$2.99","stockQuantity":0,"priceTiers":[{"qty":1,"price":"$2.99000","currency":"USD"},{"qty":10,"price":"$2.68700","currency":"USD"},{"qty":25,"price":"$2.54080","currency":"USD"},{"qty":100,"price":"$2.20190","currency":"USD"},{"qty":250,"price":"$2.08900","currency":"USD"},{"qty":500,"price":"$1.87444","currency":"USD"},{"qty":1000,"price":"$1.58085","currency":"USD"},{"qty":3000,"price":"$1.50181","currency":"USD"},{"qty":6000,"price":"$1.44535","currency":"USD"}]},"links":{"datasheetUrl":"https://cdn.icboms.com/8deb0649d3293d9a1ad791b7bc65758c.pdf","sourceUrl":null},"ai":{"faq":[{"question":"What is the closest functional second-source for OPA810IDBVR?","answer":"The LM6152ACMX/NOPB is a dual general-purpose op-amp with 80 MHz bandwidth and 30 V/µs slew rate, but it is not a pin-compatible or parametric drop-in — the OPA810IDBVR is a single JFET-input part with 254 V/µs slew rate, 2 pA bias, and industrial temperature range, while the LM6152 is a dual 500 nA-bias device with 0 °C to 70 °C rating."},{"question":"What package does the OPA810IDBVR come in?","answer":"The OPA810IDBVR is supplied in a SOT-23-5 (SC-74A) surface-mount package, available in Tape & Reel or Cut Tape options."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/texas-instruments/OPA810IDBVR","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/texas-instruments/OPA810IDBVR when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:45:10.375Z","lastPublished":"2026-07-22T19:45:10.375Z","indexable":true}}