{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"NE5532P","brand":"Texas Instruments","brandSlug":"texas-instruments","productSlug":"NE5532P","canonicalUrl":"https://icboms.com/texas-instruments/NE5532P","factsUrl":"https://icboms.com/api/mcp/products/NE5532P","rawCanonicalId":null},"summary":{"shortDescription":"Texas Instruments NE5532P dual general-purpose op-amp, 10 MHz gain-bandwidth, 9 V/µs slew rate, 8-DIP (0.300\", 7.62 mm) through-hole package, tube.","salesMarkdown":"## 10 MHz GBW and 9 V/µs slew — what they mean for the signal chain The NE5532P: For audio line-level signals (20 Hz–20 kHz), this is generous — the op-amp's open-loop gain stays well above 60 dB across the audio band, so distortion from loop-gain variation is negligible. The 9 V/µs slew rate defines the large-signal output swing before slew-induced distortion appears. Supply current is 8 mA per channel (16 mA total for the dual). That is moderate for a 10 MHz bipolar op-amp — about half what a faster part like the NE5534 draws, and a reasonable budget for a multi-channel audio mixer or active filter bank. ## Dual-channel in a DIP-8 — board-fit and replacement logic Two op-amps in one 8-pin DIP package (0.300-inch row spacing, 7.62 mm body width). The pinout is standard: pins 1–3 for channel A, pins 5–7 for channel B, pin 4 for V−, pin 8 for V+. Through-hole mounting means no reflow profile, no moisture sensitivity level (MSL) to track. The tube packaging keeps the leads straight and the bodies aligned — store the tube in an ESD-safe bin, not a dry cabinet. Hand-solder or wave-solder; the DIP footprint is the same as the LM358, TL072, or any standard dual op-amp in DIP-8. For an audio preamp in a studio rack or a signal-conditioning board in a lab instrument, it is fine. Do not spec it into an engine bay or an outdoor enclosure without a heater. ## Supply rails and output drive — what the numbers allow The 30 V maximum is the total across V+ and V−; exceeding it damages the input stage. For a ±15 V supply, the common-mode input range extends to about ±12 V, not rail-to-rail. Output current is 38 mA per channel typical. That drives a 600 Ω load to ±12 V swing, or a 32 Ω headphone to about 1.2 Vrms — enough for line-level outputs but not a speaker driver. The output stage is class AB with short-circuit protection; driving a capacitive load above 100 pF may cause ringing unless a small series resistor (50–100 Ω) is added. Input offset voltage is 500 µV typical, 4 mV maximum. For DC-coupled audio paths, the offset appears at the output multiplied by the noise gain — at a gain of 10, expect up to 40 mV DC at the output. If that matters, AC-couple the signal path or use a servo loop. Input bias current is 200 nA typical (bipolar input stage). With a 10 kΩ source impedance, the offset from bias current is 2 mV — comparable to the offset voltage itself. For source impedances above 50 kΩ, the bias current dominates the DC error; a JFET-input op-amp would be a better fit. ## Active lifecycle and compliance — no last-time-buy pressure ROHS3 compliant (no exemptions). No UL or IEC certification applies to a monolithic op-amp — the package is the only regulatory concern, and the DIP-8 is a decades-proven mold compound. No stock-holding claim — each RFQ is priced fresh.","metaTitle":"Texas Instruments NE5532P Dual Op-Amp, 10 MHz, 9 V/µs, DIP-8","metaDescription":"Texas Instruments NE5532P dual general-purpose op-amp, 10 MHz GBW, 9 V/µs slew rate, 8-DIP through-hole. Active production, ROHS3 compliant. Quoted to order.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":"ROHS3 Compliant","productStatus":"Active","categoryPath":["Analog & Data Acquisition"],"specifications":{"Mfr":"Texas Instruments","Series":"-","Packaging":"Tube","Slew Rate":"9V/µs","Output Type":"-","Part Status":"Active","Mounting Type":"Through Hole","Amplifier Type":"General Purpose","Package / Case":"8-DIP (0.300\\\", 7.62mm)","lifecycle_stage":"eol_hot","Current - Supply":"8mA (x2 Channels)","Number of Circuits":"2","Base Product Number":"NE5532","Current - Input Bias":"200 nA","Operating Temperature":"0°C ~ 70°C (TA)","Gain Bandwidth Product":"10 MHz","Voltage - Input Offset":"500 µV","Supplier Device Package":"8-PDIP","Current - Output / Channel":"38 mA","Voltage - Supply Span (Max)":"30 V","Voltage - Supply Span (Min)":"10 V"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$0.6500","priceTiers":[{"qty":1,"price":"$0.76000","currency":"USD"},{"qty":10,"price":"$0.66800","currency":"USD"},{"qty":25,"price":"$0.62760","currency":"USD"},{"qty":100,"price":"$0.51220","currency":"USD"},{"qty":250,"price":"$0.47580","currency":"USD"},{"qty":500,"price":"$0.40492","currency":"USD"},{"qty":1000,"price":"$0.32394","currency":"USD"},{"qty":2500,"price":"$0.29357","currency":"USD"},{"qty":5000,"price":"$0.28650","currency":"USD"}]},"links":{"datasheetUrl":"https://cdn.icboms.com/e5accbc911da0da6546f8f8e0a6a3e08.pdf","sourceUrl":null,"alternativesUrl":"https://icboms.com/api/mcp/products/NE5532P/alternatives.json"},"ai":{"faq":[{"question":"What is the closest functional second-source for NE5532P — LM6152ACMX/NOPB?","answer":"The LM6152ACMX/NOPB is a surface-mount (SOIC-8) dual op-amp with 80 MHz GBW and 30 V/µs slew rate — significantly faster than the NE5532P. It also offers rail-to-rail output and lower input offset (300 µV). However, it is not a pin-compatible drop-in: the NE5532P is through-hole DIP-8, while the LM6152 is surface-mount SOIC-8. A board layout change is required."},{"question":"What compliance documentation does Texas Instruments provide for NE5532P?","answer":"The NE5532P is ROHS3 compliant (no exemptions). Texas Instruments provides a ROHS3 declaration of compliance."},{"question":"What is NE5532P's listed slew rate?","answer":"The NE5532P has a slew rate of 9 V/µs. This is the large-signal parameter that limits the maximum output voltage swing without slew-induced distortion."},{"question":"What packaging does NE5532P ship in?","answer":"The NE5532P ships in a Tube (standard for through-hole DIP devices). No tape-and-reel, no moisture-sensitive bag — the DIP-8 package has no MSL rating and can be stored in an ESD-safe bin without dry-pack requirements."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/texas-instruments/NE5532P","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/texas-instruments/NE5532P when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:49:49.435Z","lastPublished":"2026-08-11T15:49:49.435Z","indexable":true}}