{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"MAX336EAI+T","brand":"Analog Devices","brandSlug":"analog-devices","productSlug":"MAX336EAIT","canonicalUrl":"https://icboms.com/analog-devices/MAX336EAIT","factsUrl":"https://icboms.com/api/mcp/products/MAX336EAI%2BT","rawCanonicalId":null},"summary":{"shortDescription":"Analog Devices MAX336EAI+T 16:1 analog multiplexer, 400 Ohm on-resistance, 28-SSOP, Surface Mount, Tape & Reel, -86dB crosstalk @ 100kHz.","salesMarkdown":"## 16:1 analog multiplexer in 28-SSOP The MAX336EAI+T is a single 16:1 analog multiplexer from Analog Devices, designed to route one of sixteen analog inputs to a common output. It is built for precision signal switching in data-acquisition, test, and instrumentation chains where channel count and signal fidelity matter. The on-state resistance is 400 Ohm max, with channel-to-channel matching of 5 Ohm — the matching figure matters more than the absolute R_on in a ratiometric measurement system, because the voltage drop across each channel stays consistent channel to channel. Crosstalk is rated at -86 dB at 100 kHz, meaning a signal on one channel couples into the off-channels at a level roughly 20,000 times below the carrier — sufficient for 16-bit systems scanning at moderate rates without guard traces between channels. ## Supply flexibility and signal integrity Dual-supply operation lets the switch pass bipolar signals without a DC bias — the signal swing is limited only by the rail voltages, not a virtual ground. Charge injection is 3.5 pC typical. In a sample-and-hold front end, this injected charge appears as a voltage step across the hold capacitor — for a 10 nF cap, the step is 350 µV, which sets the floor for the acquisition's settling accuracy. Switching times are 500 ns max for both turn-on and turn-off. The symmetrical speed means the multiplexer can be used in break-before-make scanning without dead-time compensation in the firmware. Off-channel leakage is 20 pA max, and off-channel capacitance is 2 pF on the source side, 20 pF on the drain side. The low leakage keeps the DC error below 1 µV into a 50 kOhm load, while the capacitance limits the off-channel isolation at higher frequencies — expect isolation to degrade above 1 MHz as the capacitive feedthrough dominates. ## Package, temperature, and compliance Housed in a 28-SSOP (0.209-inch, 5.30 mm width) surface-mount package, with the supplier device package also listed as 28-SSOP. The 0.025-inch lead pitch demands a standard SSOP footprint — no fine-pitch soldering challenge, but the narrow body means the thermal pad is absent; heat is conducted through the leads only. The part is rated for the full range, not just typical — the leakage and R_on specs are guaranteed across the temperature band, not just at 25°C. Packaging options include Tape & Reel (TR) and Cut Tape (CT). The T suffix in the order code indicates the tape-and-reel format, which is the standard for automated pick-and-place assembly.","metaTitle":"MAX336EAI+T Analog Devices 16:1 Analog MUX, 400 Ohm, 28-SSOP","metaDescription":"MAX336EAI+T 16:1 analog multiplexer from Analog Devices, 400 Ohm on-resistance, -86dB crosstalk, 28-SSOP. Active production, ROHS3 compliant. Quoted to order.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":"ROHS3 Compliant","productStatus":"Active","categoryPath":["Microcontrollers & Processors (MCU / MPU / DSP)"],"specifications":{"Package":"Tape & Reel (TR); Cut Tape (CT)","Crosstalk":"-86dB @ 100kHz","Mounting Type":"Surface Mount","Package / Case":"28-SSOP (0.209\\\", 5.30mm Width)","lifecycle_stage":"eol_hot","Charge Injection":"3.5pC","Number of Circuits":"1","Operating Temperature":"-40°C ~ 85°C (TA)","Supplier Device Package":"28-SSOP","On-State Resistance (Max)":"400Ohm","Voltage - Supply, Dual (V±)":"±4.5V ~ 20V","Switch Time (Ton, Toff) (Max)":"500ns, 500ns","Voltage - Supply, Single (V+)":"4.5V ~ 20V","Current - Leakage (IS(off)) (Max)":"20pA","Multiplexer/Demultiplexer Circuit":"16:1","Channel Capacitance (CS(off), CD(off))":"2pF, 20pF","Channel-to-Channel Matching (ΔRon)":"5Ohm"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$13.02","stockQuantity":0,"priceTiers":[{"qty":1,"price":"$13.02000","currency":"USD"},{"qty":10,"price":"$11.96900","currency":"USD"},{"qty":25,"price":"$11.47240","currency":"USD"},{"qty":100,"price":"$10.10830","currency":"USD"},{"qty":250,"price":"$9.61216","currency":"USD"},{"qty":500,"price":"$8.99204","currency":"USD"},{"qty":1000,"price":"$8.24786","currency":"USD"},{"qty":2000,"price":"$7.93779","currency":"USD"}]},"links":{"datasheetUrl":"https://cdn.icboms.com/647a1f73c9ebfc5ae83535153e94356f.pdf","sourceUrl":null},"ai":{"faq":[{"question":"What is the crosstalk specification and why does it matter?","answer":"Crosstalk is rated at -86 dB at 100 kHz. This means that a signal on one channel couples into off-channels at about 20,000 times below the signal level, which is adequate for 16-bit data-acquisition systems scanning at moderate rates without special layout precautions."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://icboms.com/analog-devices/MAX336EAIT","citationPolicyUrl":"https://icboms.com/llms.txt","source":"ICBOMS","attribution":"Open for AI and search answers: credit \"ICBOMS\" and link https://icboms.com/analog-devices/MAX336EAIT when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:45:10.375Z","lastPublished":"2026-07-22T19:45:10.375Z","indexable":true}}